New circuits, dedicated lines, fixtures, and equipment, wired to code and sized with your whole home in mind. Whether you're adding one outlet or wiring a whole renovation, we install it so it works the first time and for years after.
A new install is only as good as the circuit behind it. We start with capacity, not guesswork.
Electrical installation is the work of adding something new to your home's electrical system: a circuit, a dedicated line, a fixture, an outlet, or a piece of equipment that needs its own supply. It sounds simple, and a lot of it is, but the difference between a clean install and a problem down the road is all in the planning.
The key question is almost always capacity. Every new thing you add draws from the same service, and older Bergen County homes often don't have the headroom people assume. So before we run a single new wire, we look at what your panel can carry. Sometimes there's plenty of room. Sometimes a panel upgrade needs to come first, and there's a card for that just below. Either way, you find out before the work starts, not after a breaker starts tripping.
From there it's about doing it properly: the right size wire and breaker, GFCI and AFCI protection where code calls for it, a clean cable path, and a permit and inspection on anything that needs one. It's the same care we bring to our broader residential work, focused on the things you're adding rather than the things you're fixing.
Installing into an older home is its own skill. A new circuit still has to travel through walls, floors, and ceilings that were framed decades ago, and the tidy way to route it isn't always the obvious one. We plan the path to keep wall damage down, tie into the existing system cleanly, and leave you with an install that looks like it was always meant to be there, not one that was forced in.
Each of these is its own kind of install, and each has its own page with the details. Tap through to the one you need, or call and describe the project.
New and upgraded outlets, GFCI and AFCI protection, dimmers, and USB receptacles.
Recessed lighting, fixture installs, and ceiling fans, including older ceilings.
Level 2 home chargers on a dedicated circuit, sized to your panel and your car.
Standby generators with the transfer switch wired to take over automatically.
Whole-house surge protection installed at the panel to guard your electronics.
Hardwired and sealed 10-year detectors installed to current NJ code.
The capacity behind it all, so new circuits have the power to run cleanly.
Keep what we install running right with recurring checks and upkeep.
A lot of the equipment people add pulls too much to share a circuit safely. Tap what you're adding to see whether it typically needs a dedicated line of its own.
A Level 2 EV charger is a large, continuous load and always needs its own dedicated 240-volt circuit, sized to the charger and your service.
General guidance. Exact requirements depend on the specific equipment, your panel, and current code, which we confirm on site.
A dedicated circuit is a line that runs from the panel to a single piece of equipment and nothing else. It's not about doing more than you need. It's about matching the wiring to the load, so a hungry appliance isn't sharing power with half the room.
When high-draw equipment shares a circuit, you get nuisance trips at best and overheated wiring at worst. That's why code requires dedicated lines for things like ranges, dryers, and EV chargers, and why it's smart for microwaves, refrigerators, and window units too. We size each one properly, protect it where required, and label it clearly at the panel, so years from now it's obvious what feeds what. If something you already have keeps tripping, that's often a sign it needs a line of its own.
Adding a room, finishing a basement, or gutting a kitchen means a lot of new electrical, and the best time to plan it is before the walls close up. We work from your plans, rough in the circuits and boxes you'll need, and come back to trim out once the space is finished.
Bring us in early and we'll make sure the electrical plan actually fits the project, including whether your service can carry the new space. It saves the scramble of discovering, halfway through, that the panel is out of room. When the job wraps, you get the same quality wiring and documentation we bring to every install.
We handle installations across Waldwick and the boroughs around it, including Ridgewood, Ho-Ho-Kus, and Allendale, plus Wyckoff, Midland Park, Saddle River, Franklin Lakes, Glen Rock, and Ramsey. Whether it's a single new outlet or the wiring for a whole addition, you get the same shop and the same straight pricing.
Tell us what you're adding and we'll tell you what it takes, including whether your panel can carry it, all priced up front.